Menu
Build it / Crafty / DIY / woodworking

DIY Craft Table: Vintage Industrial Cart Inspired Craft Table

This project is like what you would get if a craft table and a vintage industrial cart married and had a baby. Weird I know, but that’s just how my brain works. I like to juxtapose the “what I need” with “the look I want, ” which is the result.

crafttableindustrial-8962

Because what I desired was a craft table I could move around the room. Sometimes it is convenient to be able to work on all sides of a table and other times, having a craft table in the middle of the room is just awkward and makes a space feel cramped.

crafttableindustrial-8961

I have had one of those craft tables set on top of a pair of square shelves in my studio/office for many years. It was nice to have the extra storage of all the little cubbies, but when you look at this completely embarrassing photo of my studio just before this craft table was built, it is obvious it did nothing to contribute to my tidiness. Honestly, the room has been ignored and became a dumping ground for projects. I figured the only way to encourage myself to get it tidy and keep it that way to take everything out and start over fresh. Most of what you see here are reincarnations from other, more put-together, studio rooms in my previous homes.

crafttableindustrial-8566

This craft table cart project is just step one in a complete makeover of my studio space. I truly couldn’t be more excited to finally begin to see the room moving in the direction I have long envisioned.

For your convenience, this post includes affiliate links to products used.

To build the craft table, I started with an easy to build Heavy Duty Workbench kit from Simpson Strong Tie. You can purchase one here.

crafttableindustrial-8936

With this kit you can build a strong, sturdy work table easily in a weekend. My industrial cart table probably took the equivalent of two weekends to build the top, stain and finish all the pieces, and then assemble.

Craft Table DIY industrial

By making a few modifications and embellishments, the workbench kit was transformed into this.

cart at 37

The simple sketch above will be updated with a more detailed plan and a cut list soon.

The key to part of transforming the work bench into a industrial cart was to flip the bottom brackets/connectors upside down. This allows the industrial wheels to be added and attached flush to the bottom. Don’t you just love those industrial wheels? Here’s a link to the wheels I used. I think the price is very reasonable considering how extremely heavy duty they are.

How to build an Industrial Cart Craft Table

In the traditional workbench instructions, you are supposed to use plywood for your base and top. That’s another place I went rogue. Plywood does not fit the industrial look I was after. The top and bottom shelf needed to be a bit more beefy and 2×4’s fit that bill nicely. And they are cheap!

crafttablevintage-5656

We began by deciding on final dimensions for the craft table/cart. Roughly, 51″ wide by 34″ deep was the size that best fit my space. It took (17) 2×4 boards to build this craft table, which means the wood for this project was under $40.

Begin by cutting your top 2×4’s about an inch longer than your desired length. (You will want to have extra to trim the unfinished edges straight and smooth on both sides when you are done building your top.)

crafttablevintage-5672

To create a smooth top work surface we ripped the 2×4’s down with our table saw.

For the first rip we set the saw to 3 3/8″.

crafttablevintage-5686

After cutting all 11 boards on one side, we flipped them around and set the blade width to 3 1/8″.

crafttablevintage-5688

Once the boards were all ripped, I matched up the edges to piece together the top, numbering them as I went.

crafttablevintage-5726

It is difficult to rip long 2×4 boards completely straight with a table saw. Pine 2×4’s are just not square and true, no matter how carefully you choose them at the hardware store. I marked spots where the seamed edges did not meet and used a Roybi powered hand planner to straighten or smooth them out. Don’t forget to number the boards before you move them to keep them in order.

crafttablevintage-5716

While a power planner may seem a bit intimidating and like all power tools require careful use, it is actually very easy to use and is highly effective.

Once all the edges were nice and square and fit together as seamlessly as possible, we used a Kreg Jig to join all the boards.

crafttablevintage-5731

As the boards were screwed together, we used wood glue to create a super strong bond.

crafttablevintage-5735

Because 2×4 wood also has inherent issues with cupping, we found it nearly impossible to avoid the transference of this cupping to the completed top. We did attempt to re-connect with no improvement.

crafttablevintage-5741

We improved the severity of the cupping moderately by placing scrap pieces of granite on the top overnight while the glue dried.

The rest of the imperfections were taken care of by using the planner again on the top.

crafttablevintage-5750

I began by smoothing the seams of the joints. In hindsight, I think it is better to work on getting the top level first and then, if there were still seams that need to be made smoother, then work on those.

crafttablevintage-5747

I did a good bit of research before this project and found the often repeated tip of dividing the tabletop into 4 quadrants helpful in finding and removing your high and low places. Once your problem areas are marked, you can plane the surface until it is level all the way across.

crafttablevintage-5749

As the planner removed high spots it created these divots. Those were easily removed by adjusting the dial by small increments and running the planner over the area several times.

When the table was nice and level, it was time to start sanding with an orbital sander and 80 grit sand paper.

crafttablevintage-5762

Gradually, I increased the sandpaper to 120, 220 and using a sanding block, hand sanded with 400 grit sandpaper.

About half way through this process, I used a circular saw to trim the rough edges on the sides of the table top.

crafttablevintage-5771

Using clamps, a square and the straightest 2×4 I could find, it was easy to cut a straight edge. We initally thought we would run the edge of the table through the table saw, but once the top was assembled, we realized the weight of it would make this rather difficult.

Now I was ready to move onto preparing the rest of the table parts. We cut the legs, apron runners and the deck for the bottom using a miter saw. See diagram for dimensions.

Just as described in the directions for the Simpson Strong Tie Workbench, I created notches on four of the deck boards to go around the vertical posts.

crafttablevintage-5812

To ensure a satisfactory finish, I sanded all the pieces and parts with 120 grit sandpaper.

crafttablevintage-5805

But before I began the finishing, we loosely assembled all the parts to make sure everything fit according to the plan.

crafttablevintage-5773

I wanted to create a realistic vintage look for my craft cart table. I thought a knock-off of the Salvaged Brown finish from Restoration Hardware would do the trick. I share the complete details on how I created this finish in a follow-up post, click here. Y’all, I couldn’t be more proud of how fantastic these humble 2×4’s look.

crafttablevintage-5803

With all the pieces cut and finished, it was time to gather the pieces and put it all together. It’s not unlike building with tinker toys at this point.

To build with the connectors that come in the kit, we began by installing them on the vertical posts as directed in the standard workbench instructions. I should mention that I replaced the outside screws that came with the kit with hex-head screws like these. I just thought they looked better. I continued to use the screws from the kit on the inside.

crafttablevintage-8891

Use clamps to keep the rails seated in the connector flush to keep it all square, working your way around all four corners.

crafttablevintage-8898

When you build the bottom, remember to keep the connectors “upside down” so that your project looks like a cart, not a work table with legs.

crafttablevintage-8907

Then you are ready to move on to connecting the top rails.

crafttablevintage-8911

The base should look like this when you are done.crafttablevintage-8912

Now you are ready to start adding the deck and the wheels.

crafttablevintage-8915

There were a few obstacles to overcome with installation of the wheels and the deck. Initially I was just going to nail the deck boards to rails.

But for both esthetic reasons and added strength of the connection, we attached the deck boards with counter-sunk screws. The only place this presented a bit of a problem was over the connectors in the coners.

crafttablevintage-5861

We pre-drilled through the top of the board until we hit the metal connectors. Then, using a metal drill bit we predrilled a hole for the screw through the metal.

crafttablevintage-5864

We continued screwing the first three deck boards down on both sides, pre-drilling for each hole in the boards to avoid the 2×4’s from splitting. We only did three boards on each side at this time for ease in maneuvering the base while attaching the wheels.

So, now we were ready to attach those awesome industrial wheels!

We used 3/8 x 5 1/2″ carriage bolts, nuts, washers and lock washers to attach the wheels with 4 rectangular scraps of 2×4’s at each corner.

crafttablevintage-5867

After three muddled attempts, we arrived at a process of getting the wheels attached that worked out fairly smoothly.

Begin by holding the wheel to the front of the deck where you want the wheels to be, mark with a wax or chalk pencil the position for holes and the screws. (Drilling the the holes exposed raw wood, but that was easily fixed with a small brush and stain later.)

crafttablevintage-5868

For a visual reference, this is what one of the installed wheels looks like.

crafttablevintage-5892

These scraps of plywood have been nailed and wood glued together, but not attached to the deck before the bolts go in.

With the 2 stacked scraps of plywood clamped to the back of the deck drill each hole as far as your drill bit will go.

crafttablevintage-5881

The 3/8″ wood bit we used went through the deck and partially through the first block.

Remove the clamps and the blocks and finish drilling straight through the holes created.

crafttablevintage-5886

As a safety precaution I would recommend clamping the block to something. My always cooperative hubby wouldn’t listen to my suggestion. Ha!

You will need to counter-sink the neck of the carriage bolt for to sit flush. Then, feed the bolts through the holes, the blocks of wood and attach the wheels. Even with this improved method it took a bit of coercion to get the bolts to go through the deck and the blocks. Attach the lock washers and nuts with a 9/16 wrench.

crafttablevintage-5891

Here are the wheels installed and the brackets for the wheels painted. I will cover the how I painted and created the rusty finish on these, as well as the connectors, in another post.

crafttablevintage-5893

Then we finished attaching the rest of the deck boards, pre-drilling as we went down each side.

In our initial planning, we intended to use brackets to attach the top to the apron base. But we realized we could save some money by just using a Kreg Jig to secure the top. The detailed sketch will show this step, so you can avoid making a huge mess all over your deck boards.

crafttablevintage-5894

With the top attached, we flipped the top upside down and added the sliding baskets from Target. They are actually intended to be used in wire closets or shelving. So we had to find a clever way to attach them to the top after they were given a coat of flat black spray paint.

crafttablevintage-5816

We attached runners, using a Kreg Jig, to the underside of the table top and bolted the baskets in using the hooks that were intended to hang on a wire shelf. If you’d prefer, you could always add an aluminium shelf instead. You can find metal for your DIY projects online easily from websites like this one for an aluminium warehouse metal supplier.

crafttablevintage-5899

Using the chalk pencil, we marked where the hooks hit the runners and where the runners needed to be jigged once the brackets were in place.

We pre-drilled the holes and slipped the bolts through the hook and attached nuts and lock washers to each of the sides.

crafttablevintage-5901

Then we were ready to flip the table over and slide in the baskets.

crafttablevintage-5902

They are a great alternative to an extra shelf and add to the industrial look. The generous size of the baskets allow for a lot more crafty items than what I’ve got in them now. Give me some more time and I bet I can fill them up!

crafttableindustrial-8953

To help protect the top during painting projects, I added a roll of craft paper to the side apron.

crafttableindustrial-8946

Again, we found the bolts, 3/8″x 6″ eye bolts and nuts, needed to be positioned on the metal connectors. It turns out this time, the hole fell right where one of the screws go into the brackets. We removed those screws and increased the size of the hole to accommodate the bolt and added a nut on both sides of the wood.

Then we ran a scrap piece of pipe through the bolts and hung the roll of paper. (Our scrap pipe was actually a part of an old curtain rod.)

crafttableindustrial-8976

We are almost done, but I had one more little accessory to add to this tricked out industrial craft cart! Did you notice it yet?

I nailed a vintage yard stick to the side of the table. I’ve been wondering when I’d find a use for that stash of rulers I’ve been hoarding.

crafttableindustrial-8966

I’ve got to say I’m a bit in love with my creation, the vintage industrial craft cart table. That’s a mouthful, huh?

Did you catch that this project was created solely with 2×4 lumber? It cost me under $225 to build even with all the hardware? Want to learn how to create that custom Slvaged brown finish for your next project? Click here.

RestorationhardwareSalvagedBrown

Want to see some other easy and inexpensive 2×4 projects?

Check out these other fine blogger 2×4 Challenge projects below.

Sharing here too: DIY Like a Boss

21 Comments

  • Funky Junk Interiors
    February 29, 2016 at 5:02 pm

    This project is unbelievable! I cannot believe this was just made from 2x4s… you have outstanding vision!

    Beautifully done!

    Reply
    • Leslie
      February 29, 2016 at 5:09 pm

      Donna, coming from you this is a thrilling compliment. I have long admired your creative work. Thank you for stopping by!

      Reply
  • Lisa
    March 1, 2016 at 4:46 pm

    This turned out great!

    Reply
  • Sara
    March 1, 2016 at 6:33 pm

    This is so great!!!! It look like it’s store bought, it’s that perfect!!! Love.

    Reply
  • Leanne
    March 1, 2016 at 7:45 pm

    I want this table! WOW! Great job on the 2×4 project and on a well written tutorial. I will be pinning and sharing for sure.

    Reply
  • Terry
    March 4, 2016 at 12:02 pm

    I looove absolutely every detail of this table! The paper holder, the vintage ruler … oh and the hardware! Well done indeed! You should be very proud! If you are at all interested in joining in on one more link party, I host Making Broken Beautiful every Thursday thru Sunday. It is a furniture and home decor party and I would be so happy to host your talents! I hope you have a great weekend!
    Smiles!
    Terry
    http://thecuratorscollection.wordpress.com
    Making Broken Beautiful

    Reply
  • Laurie Adams
    March 4, 2016 at 10:13 pm

    Love, love, love this table! Would also act as a GREAT gift wrapping table during the holidays….

    Reply
  • DIY Palette Day Beds in the Loft -
    April 7, 2016 at 2:23 pm

    […] The caster wheels do a nice job of getting the palettes off the floor so that the beds are not uncomfortably low to the ground. Here is a link to similar casters to the ones I used. Obviously, you could use  larger casters to get the beds up even higher.  I recently sourced these super cool casters for my Industrial Cart Craft Table. […]

    Reply
  • […] week Lucy’s pick is this fantastic DIY Craft Table, built by Leslie at Paper Daisy Designs.  Leslie added industrial rollers to the table so she could move it easily around her space. […]

    Reply
  • […] Lucy just loved Leslie’s vintage industrial cart.  And, by the way, did you notice that awesome framed print of a camera.  #love!  Find all the details about how she made the cart on her blog called Paper Daisy Design. […]

    Reply
  • Friday's Furniture Fix #34 -
    April 7, 2016 at 7:27 pm

    […] Pick from Paper Daisy Designs.  Don’t we all wish we could have a cart to roll around and use whenever and wherever we […]

    Reply
  • Victoria day
    September 14, 2016 at 10:44 pm

    I love everything you’ve made but I really like the table on wheels is it for sale and if it is what are it’s measurement from top to bottom of wheels and the size of the top and most important how much is it

    Reply
  • Leslie
    September 15, 2016 at 2:18 pm

    Victoria,
    Sorry, no the table is not for sale. However, I do offer plans on how to build your own.

    The diagram at the top of the post gives dimensions on the scale of the table.

    Thanks for reading!!

    Reply
  • […] Image via: paper daisy design […]

    Reply
  • Aimee
    October 7, 2016 at 12:27 am

    Freakin’ brilliant. I’m in love with how you did the wire basket drawers – we are building our own open shelving base cabinets in our kitchen, work-table style, and I knew I needed some kind of cool drawer situation for things like dishcloths and cloth napkins, and this is now Pinned for inspiration!

    Reply
  • Virginia Rohde
    December 27, 2016 at 1:22 pm

    Love your table. And all the things you made. I have a day bed made out of 2 x 4’s & 2 2×6’s. Better made then the store beds.

    Reply
  • […] What will stay in the room is the oversized vintage industrial cart I use as a craft table. I built it a few years ago. Tutorial can be found here. […]

    Reply
  • […] It’s such a great work surface and I am still proud of the design and the function.  Would you believe it was built solely out of 2×4’s? Yep, get all the details here. […]

    Reply
  • Bill Funderburk
    January 26, 2018 at 9:59 am

    Where did you find the corner brackets and wheels. Love the project and I was already building something similar for our pantry.

    Reply
  • […] Vintage Industrial Cart Inspired Craft Table from Deeply Southern Home […]

    Reply
  • […] Vintage Inspired Industrial Cart Craft Table from Deeply Southern Home – I totally dig those wheels and all that storage!  […]

    Reply

Leave a Reply

This site uses Akismet to reduce spam. Learn how your comment data is processed.